Facebook
Категории
Категории

Which Construction Fastener Goes Into What? Match the Screw to the Base Material

by Tianyu Fasteners
Oct 29th,2026 18 Взгляды

Which Construction Fastener Goes Into What? Match the Screw to the Base Material

Most fasteners on a European site get picked by what the installer already has in his bag. That works while the base material stays the same — but on one floor of a building it can change from galvanised channel to 18 mm MDF to teak before lunch.

The base material decides the fastener. Here is how to match them.

The base material decides

  • Gypsum board pushes back very little. Its strength sits almost entirely in the paper facing, which is why a drywall screw carries a bugle head whose trumpet curve presses the paper down without cutting it — while the thread does the real holding in the galvanised channel behind the board.
  • Sheet steel and pipe have nothing soft to bite into. The screw must make its own hole and tap a thread into the wall of that hole, so the thickness it can get through depends entirely on the drill point at the tip.
  • Timber and MDF sit in between. Chipboard needs a deep, sharp thread that cuts through without cracking or splitting the board; dense hardwood such as teak needs a wood screw of the right gauge.
  • Brick and reinforced concrete need a masonry anchor. We do not make those, so wall fixings need a different source — we will say so rather than sell you the wrong screw.

Types in our range and where each one goes

Fastener

Head and drive

Sizes

Where it goes

Tianyu SS Drywall

Bugle head, Phillips

Gauge 6 (3.5 mm) and 8 (4.5 mm), 13–75 mm

Gypsum board to GI channel, frames and TV mounts

Tianyu SDS

Self-drilling point, carbon steel

Drills 4–4.5 mm metal

Sheet metal, steel pipe, metal sub-frames

Carriage bolt

Dome head, nut from below

6 mm (38–125 mm), 8 mm (100–250 mm)

Decking, outdoor benches, structural wood joints

Machine screw

CSK, slotted or Phillips

M2–M10; BSW 1/8"–3/8" for the UK

Metal parts with a nut or tapped hole

Tianyu SS Chipboard

CSK, Phillips

M3.0–M5.0, 12–100 mm

Modular kitchens, wardrobes, MDF carcasses

Tianyu Wood Phillips

CSK, Phillips

Gauge 4–16, 12–150 mm

Timber to timber with a drill

Self-drilling screws for steel frames and sheet metal

Most self-drilling screws sold loose in the market get through 1.5–2 mm of metal and then stall — and a screw that stalls usually gets forced until the point burns out. Our Tianyu SDS is carbon steel with a drill point that goes through 4–4.5 mm thick metal.

Decking on steel needs wings. On the winged SDS, small wings ream a clearance hole through the wood, then snap off the moment they hit the steel, so the thread only starts tapping inside the metal and the plank stays down on the frame while the screw seats. When a plank lifts off the frame before the screw is fully home, that is called jacking.

Bolts and machine screws

A carriage bolt has a smooth dome head with no slot at all. The square neck under the dome bites into the wood as the nut is tightened from below, which locks the bolt against turning and leaves nothing sharp on a bench seat or deck board. We make it in stainless, in 6 mm and 8 mm diameters, lengths up to 250 mm on the 8 mm size.

A machine screw cannot hold alone: it needs a tapped hole or a nut behind it. Our stainless hex nuts and washers come in the same size range, packed 1,000 to a box.

When stainless steel is worth it

Sites get this wrong both ways — stainless into dry bedroom wardrobes where mild steel would do, and mild steel in a bathroom vanity where it rusts at the thread long before anything shows at the head.

Moisture is the whole test. Stainless belongs wherever moisture reaches the joint: bathrooms, kitchens, balconies, outdoor furniture, and any building close enough to the coast for chloride to settle on exposed metal. Mild steel is fine for interior work that stays dry — a wardrobe carcass, a false ceiling in an air-conditioned office.

Every Tianyu screw carries a 5-year rust and moisture resistance guarantee, and our stainless range also comes in silver, gold and antique black for exposed woodwork.

One exception: the SDS is carbon steel protected by its coating, so do not specify it where the drawing calls for stainless.

Checking a fastener supplier

Start with the paperwork — it is the quickest check. Ask which certifications the plant holds and which standard the screws are made to, and ask to see both in writing. Ours are CE certified, ISO 9001 certified and made to DIN 7982; a supplier who cannot name a standard gives you nothing to check the thread and head against.

Then look at the screw head: a trademark tells you who made it, which is why every Tianyu SDS carries our mark.

Then count. A pouch that says 100 should hold 100 — we pack 100 to a pouch in bundles of 2, 5 and 10, so a site store can issue exact quantities without hand-counting on the floor. Ask about dispatch last: one missing gauge can hold up a whole crew, and we dispatch within 24 hours.

What we manufacture

Tianyu Fasteners makes the site range above — drywall, SDS self-drilling, chipboard, wood screws, carriage bolts and machine screws — in stainless and carbon steel, to DIN 7982 and ISO standards, with MTC on request. Tell us your base materials and we will compile a matched site list, OEM and private-label ready, with flexible MOQs.

FAQ (for buyers and procurement)

Q: Which screw goes into a gypsum ceiling? A: A drywall screw with a bugle head, driven through the board into the GI channel so the head settles into the paper without tearing it. Gauge 6 and 8, 13–75 mm.

Q: Can self-drilling screws go through thick steel? A: Most loose-market SDS stop at 1.5–2 mm. Tianyu SDS is carbon steel and drills through 4–4.5 mm, so it handles heavier sheet and pipe.

Q: Are stainless screws needed indoors? A: Only where moisture reaches the joint. Mild steel is fine for dry indoor furniture and false ceilings; bathrooms and kitchens need stainless.

Q: What is the minimum order? A: Trial batches and full container loads are both welcome. MOQ is flexible per type.

Q: What are the lead times? A: Stock grades ship in 2–3 weeks; custom runs in 4–6 weeks after sample approval.

Contact us now for samples: support1@tianyufasteners.com. Explore our offerings at www.tianyufasteners.com.


Author: Song
Song focuses on product quality and works with our factory to deliver reliable fasteners European buyers can trust. He enjoys helping customers find the right screw and is passionate about a great experience with Tianyu Fasteners.